I wanted to build a wolfstock style delta-bot, using Makerslide linear slides. But, I wanted to run the belt through the inside of the Makerslide for a cleaner look. This is still very much a work in progress, I'm currently working on completing the design and building the printer. I'm posting a build log on my blog: http://andy-projects.blogspot.com/2013/12/delta-bot-build.html http://andy-projects.blogspot.com/2014/01/delta-bot-build-part-2-belt-tensioners.html http://andy-projects.blogspot.com/2014/01/delta-bot-build-part-3-effector-rods.html http://andy-projects.blogspot.com/2014/04/delta-bot-build-cooling-fan-magnetic.html 1.1.2014 Update: -added belt clip, bolt to back of makerslide carriage -added belt tensioner to idler bracket -added tensioner arm 1.15.2014 Update: -Added carriage mount for rod ends -Added platform (intended for budaschnozzle but lots of mounting holes for anything) -added rod sleeve (for reinforcing end of carbon rods) 1.18.2014 Update: -updated platform and rod carriage mount to improve fit with traxxas rod ends 1.19.2014 Update: -updated platform and rod carriage mounts to allow better clamping of traxxas rod ends including variability in rod end center width 3.19.2014 Update: -added shroud for 40mm fan -added bowden tube mount for Budaschnozzle -added 5mm spacer for Budaschnozzle -added platform for magnetic bearings -added carriage mount for magnetic bearings 4.03.2014 Update: -added M5 threaded rod end caps for magnetic bearings 9.8.2014 Update: -added upper and lower braces to stiffen structure. 5.15.2016 Update: -added new versions of the platform and sliders to give more clearance to tie rod ends -added improved fan shrouds, two versionsComponents required: (list in progress) Makerslide Components -3x 2040 size Makerslide, my build is using 895mm length (allowing 2x pieces cut from 1800mm sections of Makerslide) -3x carriage plate 25200-01 www.inventables.com -6x Dual Bearing V-Wheel kike 25203-02 www.inventables.com -3x Eccentric spacer 25195-02 www.inventables.com -3x Smooth Idler Wheel Kit 25197-02 www.inventables.com -9x M5 lock nuts (v-wheels) -9x M5x20 SHCS (v-wheels) Motion Control -3x 16T GT2 Pulleys -3x NEMA 17 steppers -3x GT2 belt, 198cm long each (approximately) Aluminum Extrusions -3x 1" square 8020 x 275mm (upper assembly) -6x 1" square 8020 x 250mm (lower assembly) Fasteners -3x M5x25mm SHCS (idler wheel mounts, 30mm will also work) -3x M5 nuts (idler wheel mounts) -6x M5x20mm SHCS (idler tensioner screws) -6x M5 nuts (idler tensioner nuts) -60x M5x10mm SHCS -60x M5 T-slot nuts -12x M5 x 20mm SHCS for mounting Makerslide -12x M3 x 12mm SHCS (stepper mounts) -12x M3 washers (stepper mounts) -36x M6x20mm SHCS (optional, end screws for 8020 to corners) Connector Rods -8.5mm OD x 7.25mm ID carbon rods -Traxxas 5525 rod ends (traditional rod end choice) -10mm spherical rare earth magnets + 24 5mm x 10mm SHCS with head machined (magnetic bearings)